Raised Face Rubber Gasket
Category
-
Rubber Sheeting
- Anti Fatigue Rubber Mat
- Check Plate Rubber Mat
- Electrical Insulation Rubber Mats
- EPDM Sheet
- ESD Anti Static Rubber Mats
- Fined Ribbed Rubber Mat
- Latex Sheet | Natural Rubber Sheet
- NBR Sheet
- Neoprene Sheet
- Neoprene Sheet c/w fabric insertion
- Round Stud Rubber Mat
- Rubber Sheet with Fabric Surface | SBR Sheet
- Silicone Rubber Sheet
- Willow Mat | Diamond Plate Rubber Mat
- Rubber Gasket
- Rubber Flexible Joint
- Rubber Fender
- Road Safety Rubber Products
- PVC Curtain Strips
- Anti-vibration Pad
- Conveyor Belts
- EPDM Sponge
-
Extrusion
- Custom Made Rubber Extrusion聽
- Edge Trim Door Seal | Self-Gripping Door Seal
- L Shaped Door Packing
- NBR Rubber Cord
- Rubber Container Door Seal Extrusions ( J Shaped)
- Rubber Gate Seal Extrusions
- Rubber Hatch Door Seals
- Rubber P Profile Extrusions
- Rubber Right Angle L Extrusion
- Rubber T Profile Extrusions
- Rubber Tadpole Extrusions
- Rubber Tank Strap Extrusions
- Rubber Wedges Profile Extrusions
- Rubber Weigh Bridge Seal Extrusions
- Square Solid Rubber Strip
- Fastener
-
Molded Products
- Cooling Tower Rubber Bush
- Piston Seal
- Rubber Ball
- Rubber Block
- Rubber Bush
- Rubber Cap
- Rubber Coupling
- Rubber Diaphragm
- Rubber Door Stopper
- Rubber Door Wedge
- Rubber Dust Covers
- Rubber Grommets
- Rubber Handle Cap
- Rubber Mounting
- Rubber Mounting Block
- Rubber Packings
- Rubber Ring
- Rubber Seals
- Rubber Tips
- Rubber to Metal Bonded
- Rubber Tube Stopper
- Rubber Washers
- Silicone Rubber Moulding
- Polyurethane Sheets
- PTFE Sheet & Gasket
- PVC Sheet
- Rubber Roller
Ring Type Gasket
The rig type gasket can be used for both the RF and FF flanges. It sits around the pipe bore and inside of the flange bolts, and in the RF flange, it is positioned on the raised surface. The ring type gasket is a drop-in gasket, which means it can be installed without taking apart the whole joint. It also requires less material and cutting than a full-face gasket, though it can be harder to clamp into position.
The measurements you need to know for ring type gaskets are the ID (the inside diameter or pipe bore size), the OD (the outside diameter), and the thickness of the gasket.
The Difference Between a Raised Face and Flat Face Flange
The difference between a raised face and a flat face flange is that the raised face has a raised area that surrounds the pipe bore and the flat face flange doesn’t. These are two of the most commonly used types of flange faces. They can both be sealed with one of two different types of gaskets, the ring type and the full-face gasket. This post will provide some details on the raised face flange, the flat face flange, and the two types of gaskets used with them.
Raised Face Flange
The raised face is the most common flange face type used. It’s called a raised face because it has a raised surface above the bolting circle where the gasket is placed. Sealing this type of flange face is accomplished by compressing a soft, flat, or semi-metallic gasket between mating flanges in the raised area of the flanges.
Raised face (RF) flanges are common in process plant applications but can be used in almost all applications. They are suitable for use in high and low temperatures and pressures. The purpose of the RF flange is to focus more pressure on the smaller gasket area, which increases the pressure containment capabilities of the joint.
Flanges are sized according to pressure ratings. The higher the pressure rating of the RF flange, the bigger the flange diameter, the number of bolts it requires, and the thicker both the flange itself and the raised face are.